All posts by Z3avs

Can I pm you somehow?

<p>I already try your suggestion. I have the power on and I try to continuously push the flywheel (motor) triger. then Both motor and pusher triger. But I take same results. The I try to push thw swichers instead of the triggers with tha same results also. keep in mind that for some days it works. </p>

<p>Ι try to connect both IMR batteries and normal C straight from the batteries tray to pusher. 
The result is that with IMRs the pusher can't move continuously but only with small steps its time I touch the cable on powersource. I try 2 sets of IMR batteries with same results. In the first days the IMR setup works fine but some days after problems started to appear. Please check Video with the IMR
With the C batteries it works fine. </p><p>
</p><p>
​​​​​​ </p>

<p>I charge the IMR batteries but just the same. I push the flywheel triger and motors just move very very slow, not even a full cycle. This time I switch to my old C batteries and both flywheel and pusher workds fine. The only problem which remains is that the pusher stops over darts or before them. It look that it has not enough powe to push.. or the darts are too tight in the magazine. when I smoothly try to pull out the magazine a litle whithout push the release trigger ( there is a little loose gap ). It fires fine without pusher stops. Have you heard this issue again? I thnik that the pusher need to be some mm upper. so I dont realy think tha is a trigger issue. I searched in youtube for similar issues but I didn't found anything helpfull. </p>

<p>Hi again. It looks like I have some issues with the triggers. Before the batteries upgrade The pusher stucks like it has not the enough power to push the dart. This was tha main reason I take the decision to upgrade the batteries in order to have more power. When firstly I put the IMRs all looks work fine but after some days as you see in this video the pusher works strange. I pull the trigger and almost randomly stop working or works in very low speed. Tha same happens to the flywheel triger. I open the rs to check if any safe trigger cause the issue but no. FYI. I have hack the following triggers. magazine trigger, jam door trigger and the trigger under the pusher. I hope to understand my description. Also I have shorten the trigger mechanism from the flywheel trigger to work both with the main trigger ( activates the pusher ) so when you push the main trigger the flywheel motors activated. Also I use brand new elite darts. </p><p>Is there any known issue? is an electrical problem or mechanical? in the following days I am waiting a second RS-18. I will try to use the batteries without touching the interior to see how it will performs. </p>

<p>Hi there again I just put the IMRs and all works fine until now.  </p><p>The performance is noticeable increased without any stacking issues from the pusher which I had before.
I am still waiting tha AA to C converters so I use cardboard around the batteries with tape to get the C batteries size and it works fine.  I will try it on my second rapidstrike. </p><p>For the wiring I used an 16awg cable. </p>
 <figure class="article-thumb tleft show-info-icon" style="width: 180px"> <figcaption> </figcaption></figure>

<p>Thanx mate now I feel more safe to proceed! </p>

<p>Instead of using two dummy batteries can I use a wire from the one channel and to the other put the IMR batteries, is it safe? </p><p>Also I watch this Video and this guy says that you have to rewire internal wires while using IMR batteries is this needed with 2 x IMR batteries or with more. My motors and wires will be ok? </p><p>Thank you </p>

<p>In my research on the local stores ( Greece ) I found this model .   Also for the charging device I am thinking this one LiitoKala-LII-402 </p><p>AA to C Adapter and AA Batteries Placeholders </p><p>Sorry little off topic but I found a good source to drain knowledge :D  </p><p>After the power improvements I want to try some magazines improvements. </p><p>I was thinking these mags or the original system . Is it worth it to switch to Short Darts Clip and cut the dart bullets with a utility knife.. Did I get any update in shooting performance? If you have any suggestion please let me know. </p><p>Thank you </p>

<p>Thanks a lot for your time and the advices! I have some quastions yet. 1. Can I use two empty or low AA batteries instead of dummy? 2. Can you suggest me a specific IMR model tha you have good use? 3. Do you suggest LiPos batteries instead of IMRs? </p><p>Thanx for your help </p>