All posts by Dcho4

A reply to Dcho4

Dcho4·1/6/2021

I still haven't done anything yet, but do not worry everyone. I will get this done at one point. I'm still in high school, so I've been dealing with some college stuff.

A reply to Dcho4

Dcho4·7/7/2020

Yeah, I messed up there. When my school opens again, I can use our drill press. Is the forstner recommended or required? Will the regular bits be too messy?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·7/6/2020

So the brass won’t fit in the shells, they’re about the same diameter. Should I use a drill bit to make the brass fit?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/25/2020

With the k26 adjusted to the same length as the stock spring, range does increase a bit. However, the difference is only noticeable when you angle your shots (up to 10 feet difference). I didn't expect too much improvement since it is a shotgun after all, but I'm going to start brassing the shells to see what happens. However, I noticed that the ends of the brass are very sharp and can hurt the dart if you put them in quickly. Is there a way to soften these ends?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/19/2020

Aha, I see that I may have overestimated the capability of the epoxy. I found a 7kg rampage spring, which I believe is the same as the 7kg retaliator spring, which I was originally going to purchase. I think that one should be all right since you thought the retaliator one was fine.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/18/2020

But didn’t Captain Xavier prove it can take a k26? 9kg is a lot lighter than that. As you said, he didn’t fire it repeatedly but it looks all right. I can epoxy the plunger rod and parts of the handle.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/15/2020

Sorry guys, but the 7kg retaliator spring is out of stock on outofdarts, and the next they have is 9kg longshot. Will the spring be too powerful of the stock internals?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/14/2020

Understood. I do plan on brassing the shells: should I friction-fit them or apply superglue? This is also for the lawbringer.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/14/2020

Sorry guys, just got them stripped screws out. I have the size of the stock spring and the plunger tube images. For the k26, should I order the same size as the stock spring? Should I drill off the gates i the plunger tube? Should I drill off the 3 gates in the bolt (Don't know the terminology)? <figure class="article-thumb tright show-info-icon" style="width: 180px">

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/14/2020

Sorry folks, I still don't get it. If get the concept of ghost-darting, but I don't know what difference it makes. If the AR is open whenever a dart is in there, what difference does it make by forcing it to stay open? To my understanding, whenever I shoot a dart the AR is open because of the gate. Also, is it unanimous that I should clear out the white gate thing in the plunger tube? It wasn't clear before.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/8/2020

So for the back piece, I should remove it? I'll test out the actual AR I guess, with the tooth. But the gate in the back of the tube, I should remove that one? The white piece.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/8/2020

I see. But how about the plastic one in the back-in the plunger tube-that one cannot be removed, no?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/7/2020

I’m afraid I don’t understand. The AR is still in there, but I add some piece in there?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/6/2020

Oh boy! I think I'll have to play it safe here.

(Edited by Dcho4)

A reply to TikTokIsGay70

Dcho4·6/6/2020

Tbh, I would have to go your loadout 2 and your bro's loadout 1. Shells are such a hassle in wars, and although they're a lot of fun (I have the trilogy and extra shells), they're not that effective.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/4/2020

I see—thank you. In the cases of the snipe and trilogy will TIT become a noticeable issue due to removing AR?

(Edited by Dcho4)

A reply to Dcho4

Dcho4·6/4/2020

<div class="quote">Elliottw wrote: 2. My personal experience is No, don't remove the AR. The problem is TIT (Turbulence Induced Tailspin). Excess air from the plunger tube will interfere with the darts and degrade the performance of your blaster. </div>
Is this a problem for all blasters?

(Edited by Dcho4)

Dcho4·6/4/2020 in Questions

Lawbringer modding

I have a couple questions here: 1. Should I place some 17/32 brass into each of the 12 barrels to improve range? Even though it's not a breech I saw that brassing sledgefire shells helped enormously, so it must help for these revolvers. 2. Should I take these out? <figure class="article-thumb tright show-info-icon" style="width: 180px">

(Edited by Dcho4)

A reply to Dcho4

Dcho4·5/30/2020

I’m taking mine apart to check the spring, but silly I stripped a couple of them, and I cannot get them out.

(Edited by Dcho4)

A reply to Dcho4

Dcho4·5/27/2020

This fellaused a K26, just cut down a little.

(Edited by Dcho4)